12.04.2014, 01:36
Hi,
Das Thema hatten wir hier schon mehrfach.
Das aktuellste TSB gibt ein Anzugsmoment von 215 Nm vor (unten zitiert unter 1). Auf eine Anfrage in Bowlinggreen wurde einem US C6 Owner allerdings ein Anzugsmoment von 190 Nm angegeben (zitiert unter 2). 160 Nm sind definitiv zuwenig.
zu 1:
Tapping or Scraping Noise From Rear Wheel Area (Replace Wheel Drive Shaft Nut) #07-04-95-001 - (09/26/2007)
Models: 2004-2008 Chevrolet Corvette and 2004-2008 Cadillac XLR
-------------------------------------------------------------------------------
Condition
Some customers may comment on a tapping or a scraping noise coming from the rear wheel area.
Cause
This condition may be due to the torque on the wheel drive shaft nut relaxing over time.
Correction
Replace the left and the right wheel drive shaft nut following the procedure below.
Remove the center cap from the rim.
Remove and discard the wheel drive shaft nut.
Apply LOCTITE™ 272, or equivalent, to the threads of the axle shaft.
Install the nut and tighten to the new specification.
Tighten
Tighten the nut to 215 N·m (160 lb ft).
Install the center cap to the rim.
Important: The vehicle should not be driven for 24 hours following the repair in order to allow the thread lock to cure.
Parts Information
Part Number.....10257766
Description......Nut
Qty................2 (one per side)
zu 2: Link
I used the Owner Feedback at https://www.bowlinggreenassemblyplant.com/
to ask about the Axle Nut issue.
I received a reply and asked for permission to post the fix on the forums. The information I received is as follows:
If there is presence of the nut "indexing and/or looseness", do the following:
1. Remove existing nut
2. Apply Goodwrench # 12345493 (also known as Loctite 272) on threads in area where nut finally seats
3. Install new nut (p/n 10257766)
4. Torque nut to 190Nm (140 ft-lb), static
5. Allow 24 hours cure time.
Update 9/13/2007
Part Number 12345493. has been superceded by 89021297.
LG, Joachim
Das Thema hatten wir hier schon mehrfach.
Das aktuellste TSB gibt ein Anzugsmoment von 215 Nm vor (unten zitiert unter 1). Auf eine Anfrage in Bowlinggreen wurde einem US C6 Owner allerdings ein Anzugsmoment von 190 Nm angegeben (zitiert unter 2). 160 Nm sind definitiv zuwenig.
zu 1:
Tapping or Scraping Noise From Rear Wheel Area (Replace Wheel Drive Shaft Nut) #07-04-95-001 - (09/26/2007)
Models: 2004-2008 Chevrolet Corvette and 2004-2008 Cadillac XLR
-------------------------------------------------------------------------------
Condition
Some customers may comment on a tapping or a scraping noise coming from the rear wheel area.
Cause
This condition may be due to the torque on the wheel drive shaft nut relaxing over time.
Correction
Replace the left and the right wheel drive shaft nut following the procedure below.
Remove the center cap from the rim.
Remove and discard the wheel drive shaft nut.
Apply LOCTITE™ 272, or equivalent, to the threads of the axle shaft.
Install the nut and tighten to the new specification.
Tighten
Tighten the nut to 215 N·m (160 lb ft).
Install the center cap to the rim.
Important: The vehicle should not be driven for 24 hours following the repair in order to allow the thread lock to cure.
Parts Information
Part Number.....10257766
Description......Nut
Qty................2 (one per side)
zu 2: Link
I used the Owner Feedback at https://www.bowlinggreenassemblyplant.com/
to ask about the Axle Nut issue.
I received a reply and asked for permission to post the fix on the forums. The information I received is as follows:
If there is presence of the nut "indexing and/or looseness", do the following:
1. Remove existing nut
2. Apply Goodwrench # 12345493 (also known as Loctite 272) on threads in area where nut finally seats
3. Install new nut (p/n 10257766)
4. Torque nut to 190Nm (140 ft-lb), static
5. Allow 24 hours cure time.
Update 9/13/2007
Part Number 12345493. has been superceded by 89021297.
LG, Joachim
