12.04.2011, 20:18
B0024 könnte auf ein Problem mit dem Lenkradmodul hindeuten.
Eventuell hat die Wickelfeder eine Unterbrechung oder einen Schluß.....
Aber ohne Garantie!
Aus dem Manual (Corvette C6)
DTC B0022, B0024, B0026, B0042, B0043, or B0044
Circuit Description
The driver frontal deployment loop consists of the following components:
A dual stage inflatable restraint steering wheel module
The inflatable restraint steering wheel module coil
The steering wheel module high circuits for both stages 1 and 2
The steering wheel module low circuits for both stages 1 and 2
There are 2 shorting bars used within the steering wheel module coil connector which will short together both the steering wheel module stage 1 high circuit and the steering wheel module stage 1 low circuit, and both the steering wheel module stage 2 high circuit and the steering wheel module stage 2 low circuit, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. During a frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop, in order to deploy the steering wheel module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
DTC B0022 Driver Frontal Deployment Loop (Single Stage or Stage 1) Resistance Low
DTC B0024 Driver Frontal Deployment Loop (Single Stage or Stage 1) Voltage Out of Range DTC B0026 Driver Frontal Deployment Loop (Single Stage or Stage 1) Open
DTC B0042 Driver Frontal Deployment Loop (Stage 2) Resistance Low
DTC B0043 Driver Frontal Deployment Loop (Stage 2) Voltage Out of Range
DTC B0044 Driver Frontal Deployment Loop (Stage 2) Open
Conditions for Running the DTC
Ignition 1 voltage is within the normal operating voltage range.
Conditions for Setting the DTC
DTC B0022 stage 1 or B0042 stage 2 will set when the steering wheel module deployment loop resistance is less than 1.3 ohms for 500 milliseconds.
DTC B0024 stage 1 or B0043 stage 2 will set when one of the following conditions occur:
The steering wheel module high and/or low circuits are shorted to ground or shorted to voltage for 500 milliseconds.
The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop resistance is less than 6 ohms for 500 milliseconds.
DTC B0026 stage 1 or B0044 stage 2 will set when one of the following conditions occurs:
The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop is more than 6 ohms for 500 milliseconds.
The steering wheel module deployment loop resistance is more than 4.8 ohms for 500 milliseconds.
Action Taken When the DTC Sets
The SDM commands the AIR BAG indicator ON via class 2 serial data.
Conditions for Clearing the DTC
The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
A history DTC will clear once 255 malfunction-free ignition cycles have occurred.
Diagnostic Aids
The following are possible causes of the malfunction:
A short between the steering wheel module stage 1 or stage 2, high and low circuits
An open or a high resistance in the steering wheel module stage 1 or stage 2, high or low circuits
A short to ground or a short to voltage in the steering wheel module stage 1 or stage 2, high or low circuits
The steering wheel module coil connector
The SDM connector
A malfunctioning steering wheel module
A malfunctioning steering wheel module coil
A malfunctioning SDM
Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
This step tests to see if the malfunction is caused by the steering wheel module or by the steering wheel module coil.
This step tests to see what DTCs are present. If DTC B0022 or B0042 is present, test the steering wheel module for a short between high and low circuits in stage 1 or stage 2. If DTC B0024 or B0043 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2. If DTC B0026 or B0044 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2.
Eventuell hat die Wickelfeder eine Unterbrechung oder einen Schluß.....
Aber ohne Garantie!
Aus dem Manual (Corvette C6)
DTC B0022, B0024, B0026, B0042, B0043, or B0044
Circuit Description
The driver frontal deployment loop consists of the following components:
A dual stage inflatable restraint steering wheel module
The inflatable restraint steering wheel module coil
The steering wheel module high circuits for both stages 1 and 2
The steering wheel module low circuits for both stages 1 and 2
There are 2 shorting bars used within the steering wheel module coil connector which will short together both the steering wheel module stage 1 high circuit and the steering wheel module stage 1 low circuit, and both the steering wheel module stage 2 high circuit and the steering wheel module stage 2 low circuit, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. During a frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop, in order to deploy the steering wheel module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
DTC B0022 Driver Frontal Deployment Loop (Single Stage or Stage 1) Resistance Low
DTC B0024 Driver Frontal Deployment Loop (Single Stage or Stage 1) Voltage Out of Range DTC B0026 Driver Frontal Deployment Loop (Single Stage or Stage 1) Open
DTC B0042 Driver Frontal Deployment Loop (Stage 2) Resistance Low
DTC B0043 Driver Frontal Deployment Loop (Stage 2) Voltage Out of Range
DTC B0044 Driver Frontal Deployment Loop (Stage 2) Open
Conditions for Running the DTC
Ignition 1 voltage is within the normal operating voltage range.
Conditions for Setting the DTC
DTC B0022 stage 1 or B0042 stage 2 will set when the steering wheel module deployment loop resistance is less than 1.3 ohms for 500 milliseconds.
DTC B0024 stage 1 or B0043 stage 2 will set when one of the following conditions occur:
The steering wheel module high and/or low circuits are shorted to ground or shorted to voltage for 500 milliseconds.
The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop resistance is less than 6 ohms for 500 milliseconds.
DTC B0026 stage 1 or B0044 stage 2 will set when one of the following conditions occurs:
The steering wheel module high circuit is less than 2.4 volts and the steering wheel module deployment loop is more than 6 ohms for 500 milliseconds.
The steering wheel module deployment loop resistance is more than 4.8 ohms for 500 milliseconds.
Action Taken When the DTC Sets
The SDM commands the AIR BAG indicator ON via class 2 serial data.
Conditions for Clearing the DTC
The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
A history DTC will clear once 255 malfunction-free ignition cycles have occurred.
Diagnostic Aids
The following are possible causes of the malfunction:
A short between the steering wheel module stage 1 or stage 2, high and low circuits
An open or a high resistance in the steering wheel module stage 1 or stage 2, high or low circuits
A short to ground or a short to voltage in the steering wheel module stage 1 or stage 2, high or low circuits
The steering wheel module coil connector
The SDM connector
A malfunctioning steering wheel module
A malfunctioning steering wheel module coil
A malfunctioning SDM
Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
This step tests to see if the malfunction is caused by the steering wheel module or by the steering wheel module coil.
This step tests to see what DTCs are present. If DTC B0022 or B0042 is present, test the steering wheel module for a short between high and low circuits in stage 1 or stage 2. If DTC B0024 or B0043 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2. If DTC B0026 or B0044 is present, test the steering wheel module high and low circuits for an open and for high resistance in stage 1 or stage 2.